BLE Carbon

enter image description here

The BLE Carbon is joint efforts by 96Boards and Seeed, aims to provide economic and compact BLE solutions for IoT projects.

96Boards is produced by Linaro, a nonprofit oganization cofunded by famous companies including ARM, IBM、Samsung、ST-Ericsson and TI. It is the first open specification to define a platform for the delivery of compatible low-cost, small footprint 32-bit and 64-bit Cortex-A boards from the range of ARM SoC vendors. By standardizing expansion buses for peripheral I/O, display and cameras, it allows the hardware ecosystem to develop a range of compatible add-on products that will work on any 96Boards product over the lifetime of the platform.

BLE Carbon is the kind of boards that uses software platform from 96Boards while the hardware from Seeed, it also uses the Nordic bluetooth solution. With the widely used open specification and strong manufacturing background from 96Boards and Seeed, BLE Cardon must be one of the best BLE solutions for IoT project.

The Carbon comes pre-installed with Zephyr. When future OS become available, you may refer to the download page for more OS and applications.

##Features

###Microcontroller features

STM32F401RET6 in LQFP64 package
ARM?32-bit Cortex?-M4 CPU with FPU
84 MHz max CPU frequency
VDD from 1.7 V to 3.6 V
512 KB Flash
96 KB SRAM
GPIO (50) with external interrupt capability
12-bit ADC with 16 channels
RTC
Advanced-control Timer
General Purpose Timers (7)
Watchdog Timers (2)
USART/UART (4)
I2C (3)
SPI (3)
SDIO
USB 2.0 OTG FS

###Board features

STM32F401 microcontroller with 512kB Flash, 96kB ram
USB power supply with fuse protect
6LEDs
- USR1, USR2, BT, PWR, RX, TX
Two push buttons
- USR and RESET
SWD debug connectors
On board chip antenna
3.3V work voltage
2x15pin 2.54mm pitch Low speed connector
Fully compatible with 96Boards IoT standards

##Specifications

Parameter	Value
Chipset	STM32F401
BT	nRF51822
Clock Speed	84MHz max CPU frequency
Flash	512KB
SRAM	96KB
Digital Output Voltage	3.3V
Analog Pins	6
Analog Input Voltage	0~3.3V
Dimensions	60x30mm

##Hardware Overview

enter image description here

1.OTG - Can be used as USB OTG/HOST and USB device, also used for USB DFU.

2.LED Indicators

USR1 - User controlled led, connected to PD2
USR2 - User controlled led, connected to PA15
BT - Bluetooth indicator, connected to PB5. This led will light up when connect to a device.
PWR - Light up when Power on.
RX - Indicator of FT230X - RX
TX - Indicator of FT230X - TX

3.UART - for debugging or firmware update, connected to USART1.

4.Reset Button - Press to reset the system

5.BOOT0 Button - user button or select boot mode, connect to PC12, default low.

6.UART and SWD for debug (STM32F401 and nRF51822 both)

7.BT Chip antenna

8.Pins - Details refer to Pin map

9.IC1 - FT230X

A.IC2 - STM32F401

B.IC3 - nRF51822

##Pin Map

note

Click to view larger image.

##Connection between nRF51822 and STM32F401

If you want to use a BLE SoftDevice in applications that cannot be ported to nRF5, for example because they use specific peripherals or need more resources like RAM, flash memory, or CPU sped, you should consider using serialization.

###Hardware connection Hardware connection as below:

STM32F401	nRF51822	function
PA4	P0.25	SPI_CSN
PB1	P0.28	SPI_REQ
PB0	P0.29	SPI_RDY
PA7	P0.00	SPI_MOSI
PA6	P0.30	SPI_MISO
PA5	P0.07	SPI_CLK
PB2	SWDIO/NRESET	RESET

###Serialization software setup Prepare the connectivity board by performing the following steps:

Connect the board to the computer and make sure that the RESET wire is disconnected.
Program the SoftDevice on the connectivity board. See Programming SoftDevices for instructions.
In Keil, open the Connectivity Example for the physical transport layer that you want to use: \examples\ble_central_and_peripheral\ble_connectivity\board\ser_s13x_spi
Compile the application and download the created.hex file to the connectivity board.

For more details, please refer to Running a serialized application

##How to upgrade firmware

###DfuSe demonstration procedures ####How to download a DFU file

Press BOOT0 button and connect OTG to your PC.
Run the DfuSe demonstration application (Start -> All Programs -> STMicroelectronics -> DfuSe Demonstration).
Click the Choose button (Item 1 in following figure) to select a DFU file. the displayed Information such as VID, PID, Version and target number is read from the DFU file.
Check the Optimize upgrade duration checkbox to ignore FF blocks during the upload.
Check the Verify after download checkbox if you want to launch the verification process after downloading data.
Click the Upgrade button (Item 2 in following figure) to start upgrading file content to the memory.
Click the Verify button (Item 3 in following figure) to verify if the data was successfully downloaded.

enter image description here

####How to generate DFU files from S19/Hex/Bin files

Run the DFU File Manager application (Start -> All Programs -> STMicroelectronics -> DFU File Manager).
Select I want to GENERATE a DFU file from S19, HEX or BIN files item in the Want to do dialog box hen click OK.
To create the image from an S19 or Hex file, click the S19 or Hex button and select your file, a DFU image will be created for each added file.
To create the DFU file, click Generate.

note

 For more details, please to read the user manual([UM0412](http://www.st.com/content/ccc/resource/technical/document/user_manual/3f/61/72/ff/c5/5a/4a/7b/CD00155676.pdf/files/CD00155676.pdf/jcr:content/translations/en.CD00155676.pdf)) from ST.

###6.2 Download a hex file through UART

Press BOOT0 button and connect UART to your PC.
Run the Demonstrator GUI application (Start -> All Programs -> STMicroelectronics -> Demonstrator GUI).
Follow the steps below to download the firmware.

enter image description here